軟管泵工作原理：
一根內壁光滑，強度可靠的特制橡膠軟管安裝在泵體內部，通過一對壓輥沿著軟管旋轉擠壓，這樣的 旋轉使得介質往一個方向輸送而不會倒流，軟管在輸送介質之后，由被壓扁軟管的自身彈性和側導輪的強制下，軟管恢復原狀，此時，軟管內產生高真空將介質再次吸入管腔，然后介質在隨之而來的壓輥擠壓下從軟管內排出，如此周而復始，介質不斷的被吸入和排出。目前產品使用溫度為≤100℃。根據用戶需要可以開發使用溫度在120℃的軟管泵軟管產品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.

軟管泵的使用注意事項：
1、使用軟管泵時調壓板請不要擰得太緊，以免“扎死”泵頭，一般調到有液體流出即可，以延長其使用壽命。  
2、泵頭在快速運轉中，切勿按動“順/逆”開關，若要按動，則先將速度調慢后再按動，然后再將速度調至原來速度，即將電壓表讀數調至原來值。  
3、軟管泵在使用期間，應隨時注意軟管是否完好，一般在中速情況下運轉為佳，當發現軟管使用老化時，應及時更換軟管。  
4、使用完畢要將泵頭清洗干凈，若長時間不使用，應取下軟管，以延長其使用壽命。  
5、軟管泵長期不用時，請把軟管從泵頭中取出，延長其使用壽命。軟管是易損物品，使用一段時間后請及時更換。不然會造成漏液，損壞儀器！  
6、根據不同介質和不同流量，請選用不同粗細的軟管。