www.eayco.com
將連接泵進出口的管道拆開，并將冷卻液放出。將進出口管夾內六角螺栓（各四個）擰下。短接管及管卡取出。將進出口前接管螺栓旋出，將前接管、壓環及密封圈取出。啟動電機，使電機順時針旋轉，將軟管拉出。啟動電機，使電機逆時針旋轉。將新軟管一側涂少量潤滑脂（黃油），然后將涂有潤滑脂的一側向泵殼壁，從泵殼上方插入至泵殼中，直至軟管到泵殼下方出口的合適位置，停電機。將密封圈套至軟管下口泵接管內，將壓環裝入，擰緊前接管螺栓，裝入管夾，擰緊管夾螺栓。啟動電機，使電機逆時針旋轉，用手或橡膠板堵住軟管上方口，軟管全自行進入泵中，通過泵側面窗口觀察，使軟管貼到泵殼內壁，停電機，按固定的方式將軟管安裝好。填加冷卻液，軟管更換即告完成。
豫信致誠機械設備(煙臺市分公司)生產的 水渠機，通過了ISO9001：2000國際質量管理體系認證，擁有完善的質量保證體系和先進的管理模式，并被認定為省級“重合同守信用企業”、“質量信得過單位”、“5.18質量、信譽、服務消費者滿意單位”等。
工業軟管泵不銹鋼齒輪泵，可輸送非潤滑油飲料低腐蝕性液體，配銅齒輪可輸送汽油苯等低內點液體。由于齒輪泵自吸能力差，一般是由于齒輪泵泵腔間隙較大所致。同時也是如果齒輪泵輸出端沒有“止回閥”，則必須是下一級齒輪泵的止回閥或控制閥。移動固定后，周圍工作人員可恢復手術。
Industrial hose pump stainless steel gear pump, can transport non-lubricant beverages with low corrosive liquids, with copper gears can transport gasoline, benzene and other low internal point liquids. Due to the poor self-priming ability of the gear pump, it is generally caused by the large gap between the pump cavity of the gear pump. At the same time, if there is no "check valve" at the output of the gear pump, it must be a check valve or control valve of the next gear pump. After moving and fixing, the surrounding staff can resume surgery.
軟管泵屬于蠕動泵的范疇，主要是由一根特制的橡膠軟管，對應泵體內轉子總成上的一對壓輥，當壓輥沿著橡膠軟管轉動時，壓輥與泵殼產生的擠壓力將橡膠軟管壓扁，在軟管自身彈性和側導輥的強制下，通過恢復原狀產生的真空吸入流體物料，物料在壓輥的機械擠壓下從管內排出，如此往復循環，從而達到連續輸出物料的目的。
The hose pump belongs to the category of peristaltic pump. It is mainly composed of a special rubber hose corresponding to a pair of pressure rollers on the rotor assembly in the pump body. When the pressure roller rotates along the rubber hose, the pressure roller and the pump housing The squeezing force flattens the rubber hose. Under the elasticity of the hose itself and the force of the side guide rollers, the fluid material is sucked in by the vacuum generated by the original state. The material is discharged from the tube under the mechanical pressure of the pressure roller, and so on. , So as to achieve the purpose of continuous output of materials.
