電工鋼硅鋼片本文件適用于寶山鋼鐵股份有限公司生產的、安徽淮北同城用于頻率在 100Hz-10000Hz 磁路結構的、安徽淮北同城以終退火狀態交貨的全工藝冷軋無取向電工鋼帶產品(以下簡稱產品)，比總損耗(鐵損)specific total loss (iron loss)比總損耗是指在磁極化波形保持正弦，其峰值和頻率為特定值時，單位質量材料所消耗的總功率，比總損耗用符號 P(Jm/f)表示，單位為 W/kg。例：P1.0/400表示在 磁極化強度為 1.0T、安徽淮北同城頻率為 400Hz 時的比總損耗。Q/BQB 481－202123.2 磁極化強度 magnetic polarization磁極化強度是指試樣受交變磁化時，特定磁場強度峰值的磁極化強度峰值，其符號為J(H)，單位為 T(特斯拉)。例：J5000表示對應于磁場強度峰值為 5000A/m 下的磁極化強度峰值。4 分類本文件的材料的等級是根據磁極化強度在1.0T、安徽淮北同城頻率在400Hz下的 比總損耗值P1.0/400、安徽淮北同城材料公稱厚度進行牌號分類，并按產品特性細分為普通型、安徽淮北同城型、安徽淮北同城高強度型、安徽淮北同城高磁感型和高強度型五類。示例 1：B20AV1300 表示公稱厚度為 0.20mm 的普通型無取向電工鋼， 比總損耗P1.0/400為13W/kg；示例 2：B27AHV1400 表示公稱厚度為 0.27mm 的型無取向電工鋼， 比總損耗P1.0/400為14W/kg；示例 3：B30APV1500 表示公稱厚度為 0.30mm 的高磁感型無取向電工鋼， 比總損耗P1.0/400為15W/kg；示例 4：B25AHV1300M表示公稱厚度為0.25mm的高強度型無取向電工鋼， 比總損耗P1.0/400為13W/kg；示例 5：B35AHS500 表示公稱厚度為 0.35mm 的高強度型無取向電工鋼，小屈服強度500MPa。1 絕緣涂層狀態產品通常以兩面涂敷絕緣涂層狀態交貨，涂層種類見表 2。絕緣涂層應可耐受絕緣漆、安徽淮北同城變壓器油、安徽淮北同城機械油等介質的侵蝕。本文件規定的絕緣涂層與國內外相關技術規范規定絕緣涂層的近似對照可參見附錄 A(資料性附錄)，絕緣涂層的特性見附錄 B(資料性附錄)。絕緣涂層的厚度、安徽淮北同城自粘接涂層的剝離強度等技術要求如有特殊要求應在訂貨時協商，并在合同中注明。涂層絕緣電阻涂層絕緣電阻分為表面絕緣電阻和層間電阻，表面絕緣電阻單位為Ω·cm2/面，層間電阻單位為Ω·cm2/片，理論上，層間電阻是表面絕緣電阻的 2 倍。根據需方要求，經供需雙方協商，可進行涂層絕緣電阻的檢測，并在合同中注明涂層表面絕緣電阻或?qū)娱g電阻的小值。

電工鋼硅鋼片In addition to the types listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, used for medium and high-frequency motors, transformers, and pulse transformers； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding.Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength [1] [2]. The requirements for the performance of electrical steel plates are as follows:Low core loss (PT)Iron core loss refers to the ineffective electrical energy consumed by an iron core when magnetized in an alternating magnetic field of ≥ 50Hz, abbreviated as iron loss, also known as alternating loss, and its unit is W/kg. The ineffective electrical energy consumed due to various obstacles caused by magnetic flux changes not only loses electrical energy through the heating of the iron core, but also causes temperature rise of the motor and transformer. The iron loss (PT) of electrical steel includes three parts: hysteresis loss, eddy current loss (Pe), and anomalous loss (Pa). Electrical steel plates have low iron loss, which can save a lot of electricity, prolong the operating time of motors and transformers, and simplify cooling devices. Due to the iron loss of electrical steel plates, which accounts for 2.5％ to 4.5％ of the annual electricity generation in various countries, countries always try their best to reduce iron loss in the production of electrical steel plates, and use iron loss as the most important indicator to assess the magnetic properties of products. The iron loss value of products is used as the basis for classifying product grades. Cold rolled oriented electrical steel: Cold rolled oriented electrical steel is a high-end product in the field of electrical steel. Compared with cold rolled non oriented electrical steel, its magnetism has strong directionality； It has superior high magnetic permeability and low loss characteristics in the direction of easy magnetization rolling. The iron loss of oriented steel strip in the rolling direction is only 1/3 of that in the transverse direction, and the ratio of magnetic permeability is 6:1. Application: The main purpose of cold-rolled oriented silicon steel strip is for transformer manufacturing.Full process cold rolled non oriented silicon steel coating: The surface of the full process cold rolled silicon steel is coated with a semi transparent insulation coating, which has different codes in different standards. Taking Baosteel‘s Q/BQB 480 2014 as an example:

電工鋼硅鋼片鐮刀彎產品的鐮刀彎規定僅適用于切邊供貨的狀態。在任意 2m 測量長度上，鋼帶的鐮刀彎應不大于2mm。供方如能保證，可不進行該項檢測。7.3.5 毛刺高度剪切毛刺高度的規定僅適用于以切邊交貨的材料。剪切毛刺高度應不大于0.035mm。7.3.6 殘余曲率產品的殘余曲率通過測試鋼片的底邊和支撐板間的距離確定。鋼帶的殘余曲率應不超過35mm。供方如能保證，可不進行該試驗。7.4 技術特性Q/BQB 480－202187.4.1 約定密度用于計算產品的磁性能和疊裝系數的約定密度應符合表 3、安徽淮北表 4 的規定。如需采用其他約定密度，須供需雙方協商后確定。