軟管泵工作原理：
一根內壁光滑，強度可靠的特制橡膠軟管安裝在泵體內部，通過一對壓輥沿著軟管旋轉擠壓，這樣的 旋轉使得介質往一個方向輸送而不會倒流，軟管在輸送介質之后，由被壓扁軟管的自身彈性和側導輪的強制下，軟管恢復原狀，此時，軟管內產生高真空將介質再次吸入管腔，然后介質在隨之而來的壓輥擠壓下從軟管內排出，如此周而復始，介質不斷的被吸入和排出。目前產品使用溫度為≤100℃。根據用戶需要可以開發使用溫度在120℃的軟管泵軟管產品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.

軟管泵性能<br />
軟管泵性能的兩個主要參數為排量和壓力。排量以每分鐘排出若干升計算?它與鉆孔直徑及所要求的沖洗液自孔底上返速度有關，即孔徑越大，所需排量越大。要求沖洗液的上返速度能夠把鉆頭切削下來的巖屑?巖粉及時沖離孔底，并可靠地?cái)y帶到地表。地質巖心鉆探時一般上返速度在0.4～1米/分左右。<br />泵的壓力大小取決于鉆孔的深淺沖洗液所經過的通道的阻力以及所輸送沖洗液的性質等。鉆孔越深管路阻力越大、需要的壓力越高。隨著鉆孔直徑，深度的變化，要求泵的排量也能隨時加以調節。在泵的機構中設有變速箱或以液壓馬達調節其速度、以達到改變排量的目的。為了確掌握泵的壓力和排量的變化軟管泵上要安裝流量計和壓力表，隨時使鉆探人員，解泵的運轉情況同時通過壓力變化判別孔內狀況是否正常以發生孔內事故。！